Spec Sheet: 

Spec Sheet | Drawings | Literature

You can copy and paste this information into your word processor.

General
Flap gates and accessories shall be of the size, material and construction shown on the drawings and specified herein. They shall by Hydro Gate heavy-duty flap gates or approved equal, with circular, square or rectangular openings. Similar installations shall have operated successfully for five years or more. All component parts shall be of the type material shown in the “Materials” section of this specification. The Material Combination Number applicable to each gate shall be shown in the “Gate Schedule.”

Seat
The seat shall be flat back and shall be cast in one piece with a raised section around the perimeter of the waterway opening to mount the seating faces. The raised section shall provide a seating plane diverging top to bottom from the plane of the mounting flange to assist in positive closure of the cover. The seat shall be shaped to provide two bosses extended above the top of the waterway opening for mounting the pivot lugs. Pivot lug bosses shall be drilled and tapped for mounting studs. The back of the seat shall be machined to a plane and drilled to mate the anchor or stud layout. Gates attached to concrete shall be mounted on anchor bolts and grouted in place.

Cover
The cover shall be cast in one piece with necessary reinforcing ribs, a lifting eye for manual operation, and with bosses to provide a pivot point connection with the links. Bosses shall be designed to place the hinge pins in double shear when the gate is assembled.

Seating Faces
A full-width, dovetail slot shall be machined around the perimeter of the cover and the seat. Corrosion-resistant dovetail seating faces shall be mounted in the slot and held securely without use of screws or other fasteners. The seating faces shall be machined to a plane with a minimum 63 micro-inch finish.

Flap gates subjected to mild slamming action shall have a rubber seating face on the seat. Rubber seating faces shall be mounted in a dovetail slot and held securely without use of pins or screws. The seating face on the cover shall be as specified in the previous section.

Pivot Lugs
Each pivot lug shall be cast in one piece. Lugs shall have double bosses to place the top hinge pins in double shear when they are assembled through the link. The lugs shall be adjustable in the horizontal plane without removal of the cover from the gate links. The adjustment shall allow the top pivot point to be moved toward the gate seat for reduced sensitivity of the cover, or moved away from the gate seat to provide opening with minimum differential head. Two corrosion-resistant studs shall be used to connect each pivot lug to the gate seat.

Links
The links connecting the cover and pivot lugs shall be heavy duty and cast in one piece. Each link shall be provided with commercial grade, corrosion-resistant bushings at each pivot point. The bottom of the links shall be provided with an adjusting screw to properly align seating faces on the cover with respect to the seat. The links shall be designed to limit the double hinge action, preventing the cover from rotating sufficiently to become wedged in the open position.

Fasteners
All anchor bolts, assembly bolts, screws, studs and nuts shall be of ample size to safely withstand the forces created by operation of the gate under the heads shown in the “Gate Schedule”. Quantity and size of the fasteners shall be of recommended by the manufacturer. Anchor bolts shall be furnished with two nuts each to facilitate installation and alignment of the gates when attached to concrete.

Painting
Machined surfaces shall be coated with a water-resistant, rust-preventive compound. All cast iron parts shall be shop cleaned and painted in accordance with the manufacturer’s standard practice.

Drawings for Approval
Drawings showing the dimensions and details required to locate and install the component assemblies shall be submitted for the engineer’s approval prior to fabrication.

Installation
Installation of all parts shall be done by the contractor in a workmanlike manner and in accordance with the manufacturer’s instructions. It shall be the contractor’s responsibility to handle, store and install the gate in strict accord with the manufacturer’s drawings and recommendations.

Materials
The “Material Combination Number” included in the “Gate Schedule” and shown below defines the type of material for the component parts of the gates and accessories included in this specification. Materials shall conform to the requirements of the following ASTM standards. When more than one alloy, type or grade of material is shown, the exact alloy furnished must be at the manufacturer’s option.

Cast Iron
ASTM A126, Class B

Austenitic Gray Iron Casting
(Ni-Resist) ASTM A436, Type 2

Stainless Steel (Faces & Anchors)
ASTM A276, Type 302 or 304

Stainless Steel (Fasteners)
ASTM F593 (Bolts), Alloy Group 1

Monel (Seating Faces and Fasteners)
ASTM B164, Class A or B

Naval Bronze (Seating Faces)
ASTM B21, Alloy 482

Silicon Bronze (Seating Faces)
ASTM B98, Alloy 651

Rubber (Seating Faces)
ASTM D2000, Grade 1BE625

Bronze (Bushings)
ASTM B584, Alloy 932

Stainless Steel (Bushings and Pins)
ASTM A582, Type 303

copyright 2019 hydro gate | all rights reserved. Hydro Gate Company is a subsidiary of Mueller Water Products, Inc.
privacy policy
HENRY PRATT | MILLIKEN VALVE | US PIPE